通用banner
Your current location : Home >> News >> Technical Information

KeywordsKeywords

ContactContact Us

Guangdong Tongde Lighting Co., Ltd.

Contact person: Mr. Li

Mobile: 18128207876

Hotline: 400-0760-789

QQ email: 316567721@qq.com

QQ:316567721

web:en.tongdelight.com

Factory address: No.6 Beiyuan Road, high tech Zone, Waihai street, Jiangmen City, Guangdong Province

Store address: card 5-11, building B, Caoer international street lamp city, Guzhen Town, Zhongshan City

Solutions for LED lamp failure

2021-05-28 09:50:18
a

LED lamps are energy-saving, high-brightness, long-life, and low failure rate. They have become a luminous body that ordinary household users like. However, a low failure rate does not mean that there is no failure. What should we do when the LED light fails? In fact, the cost of repairing LED lights is very low, the technical difficulty is not high, and ordinary people can operate it.



The lamp bead is damaged


After the LED lamp is turned on, some of the lamp beads do not light up, basically it can be judged that the lamp beads are damaged. The damaged lamp bead can generally be seen with the naked eye-there is a black spot on the surface of the lamp bead, which proves that it has been burned. Sometimes the lamp beads are connected in series and then in parallel, so the loss of a certain lamp bead will cause a lamp bead to not light up. We provide two maintenance programs according to the number of damaged lamp beads.


1. A small amount of damage


If only one or two lamp beads are broken, we can repair them by these two methods:


Find the broken lamp bead, connect the metal at both ends of it with a wire, and short-circuit it. The effect of this is that most of the lamp beads can light up normally, and only the broken individual lamp beads do not light up, which has little effect on the overall brightness.


If you have strong hands-on ability, you can buy the same type of lamp beads online and replace it yourself-use an electric soldering iron (heat the old lamp beads until the glue on the back of the old lamp beads is melted, then use tweezers to remove the old lamp beads Remove. At the same time, install the new lamp beads while it is hot, and you're done!


Second, a large amount of damage


If a large number of lamp beads are damaged, it is recommended to replace the entire lamp bead board. The lamp bead board is also available online. Pay attention to three points when buying: 1. Measure the size of your own lamp; 2. Look at the appearance of the lamp bead board and the starter connector; 3. Make a note of the output power range of the starter.


These three points of the new lamp bead board must be the same as the old lamp bead board-replacement of the lamp bead board is very simple. The old lamp bead board is fixed on the lamp holder with screws and can be removed directly. The new lamp bead board is fixed with magnets. When replacing it, remove the new lamp bead board and connect it to the connector of the starter.


Damaged starter


Most of the LED lamp failures are caused by the starter. If the lamp does not light up at all, or the lamp flickers after being turned on, the starter is probably broken.


The starter cannot be repaired, so it can only be replaced with a new one. Fortunately, the new starter is not expensive. Pay attention to three points when buying a new launcher:


1. Pay attention to the appearance of the connector, if the starter is male, the lamp bead board is female; vice versa.


2. Make a note of whether your lamp can change color and several colors. The number of discolorations of the new starter must be the same as that of the old starter.


3. Make a note of the output power range of the starter-a range will be marked on the starter, as long as the power of the lamp bead board is within this range.


The replacement is still very simple, first separate the starter from the lamp bead plate, the starter is also fixed on the base with screws, and you can remove it. The new starter is also a magnet, so it can be sucked and connected to the lamp bead board.


Contact

Factory address: No.6 Beiyuan Road, high tech Zone, Waihai street, Jiangmen City, Guangdong Province

Store address: card 5-11, building B, Caoer international street lamp city, Guzhen Town, Zhongshan City

Mobile: 18128207876 (Mr. Li)

Hotline: 400-0760-789

QQ email: 316567721@qq.com

QQ:316567721